How do you get a marquise stone to sit snug in a hammered copper ring without cracking everything?

Nov 19, 2026 Last reply: 1 hour ago 3 Replies

First reply

abecker60

Yeah, all the hammering needs to happen before the stone goes in, full stop. That's not just you forgetting, that's the actual order of operations. Copper moves every time you hit it, so a plate that was perfectly flat when you set the stone will twist and bow the second you…

Read the full reply

So I've been trying to make these big statement rings out of copper sheet, the kind with layered plates running down the finger like little suits of armor. Hammered the heck out of them for texture, then oxidized the whole thing dark. Looks awesome if I'm honest, but the part that's driving me nuts is the stone.



I'm setting a marquise-cut crystal in the center of the top plate and I cannot get it to sit tight. There's always a tiny gap on one end or the other, no matter how carefully I file the seat. Do you guys cut the seat first and fit the plates around it, or build the plate and cut the seat after? I've been doing it the second way and I wonder if that's my whole problem. Also, when I hammer the plates after setting the stone to add more texture, the setting always loosens up a bit. Am I supposed to do all the hammering before the stone ever goes in? Feels obvious now that I type it out but I keep forgetting and re-doing work. Any tricks for keeping the prongs tight while I'm whacking away at the rest of the ring would be appreciated.


Yeah, all the hammering needs to happen before the stone goes in, full stop. That's not just you forgetting, that's the actual order of operations. Copper moves every time you hit it, so a plate that was perfectly flat when you set the stone will twist and bow the second you texture it. The setting loosens up because the whole plate is flexing under your hammer, not because the prongs failed. Do your forming, texturing, and even the file work on the edges first, get the plate to a state where you'd call it done if the stone weren't there, and only then cut the seat and set.

For the gap problem, the way I do marquise seats is to cut them, fit the stone, and then re-check the flatness of the whole plate afterward. Cutting a seat involves filing and pressure, and that alone can rock a thin plate out of true. So the sequence is: flatten the plate, cut the seat, drop the stone in, look at it from the side against somthing flat, and if the plate has warped at all, gently re-flatten it with the stone still seated or pulled out, then re-fit. A gap at one point of a marquise is almost always the seat being tilted or the two ends not sitting at the same height, not the seat being the wrong length. Check that the stone sits level before you worry about the prongs. One trick for the points of a marquise, since that's where these always go wrong: the points are super fragile and the seat has to actually support them, not just the sides. If your bearing is only along the shoulders of the stone, the ends will always look gappy.

If you really want texture near a finished setting, use a punch and chase it from a distance rather than hammering the plate itself, and keep a scrap of leather or hard wood between your tool and anything near the prongs. But honestly, save yourself the headache and texture everything first. Plan the rough spots where the hammer will fall, leave the seat area alone, and set last.

Been doing this since before laser cutters and CAD, and I'll tell you what saved my sanity with copper: anneal it, do all your hammering, then anneal again before you even think about the seat. Copper work-hardens fast and a stressed plate will keep shifting for days after you set the stone, not just while you're at the bench. I also made myself a little wood dapping block years back, back when all we had was a ring mandrel and prayer, and pressing the plate flat against it beats hammering for the final truing up. One question though, are you checking the stone level against the finger, or against the plate? Those armor-style stacked rings can read straight on the bench and still sit crooked on a hand.

One thing that helped me with layered plate designs was keeping a dummy stone on hand, just a cheap reject crystal or even a bit of brass filed to the same outline, so I could test the seat repeatedly without risking the real stone chipping at the points. I'd scribe the seat location onto the plate before any hammering too, because after you've textured everthing it's surprisingly easy to lose track of where the center actually is once the surface is covered in facet marks. Also, pedantic side note, what does 'made by lifting' mean in the title, is that a translation thing or an actual technique I haven't heard of?

Join the Discussion

Have something to add? Share your thoughts — no account required.

Didn't find your answer?

Ask the community — no account required