Kilns

Hi ,I am looking for a kiln to fuse,slump,cast,ect. There are so many different ones out there and I am afraid of getting the wrong one and being sorry I didn't get a different one, so any advise would be helpful. I have been looking at the 1014 skirt with the glass-master control and also the paragon.22 " front load,what does anyone think about those two? Suzi ;

Reply to
misstiki
Loading thread data ...

Tell us first what are you going to use the kiln for. If you make jevelry your requirements are different of those needed for fusing-slumping bowls not to mention casting solid pieces.

Tell us second if you are inclined to production work or one of the kind pieces.

-lauri

Reply to
Lauri Levanto

Hi Lauri,I am not into jewerly.I want to be able to do custume work some day in hopes of earning a few extra dollars.I would like to fuse art pieces of fair size ,slump plates, drop ring cool vases,some day even do sinks.I know that sounds ambicious for a beginner but I love working with glass and want to branch out from stained glass a little. Suzee

Reply to
misstiki

Get the largest kiln you can afford. A bell or top loader. I built a 3x5 a few years back but am regularly using a Denver 4x8 right now.

Jack

Reply to
nJb

Thanks for the info. Art pieces of fair size? A round plate of 20" diam is someting in a display. Some pieces may be rectangular. So a working surface of 20"x32" might do? Drop ring calls for 8" working height + 6" distance to top elements.

Mine is a bit smaller, It was limited by the fact that I could not get more than 230V 3*16A electricity. calculate the cubic feets, I'll not tease my mind with imperial units. Compare that to kiln brochures and you get an idea what is feasible.

Jack gave the usual recommendation "bigger is better" but I do not completely agree unless you plan production work. In artistic work you want to do one piece at time not to compromise quality. Most pieces will be smaller that the show cases above. I hate to heat up that mass for a test piece of the size of a postcard. Consider also a "starter" that can serve as a test kiln later on, when you know more of the direction your works are going. I would say the kiln must be big enough for 90 per cent of your projects. The larger ones a re usually commissions and the you can afford to hire kiln time somewhere.

I love my bell jar, as it has minimal heat radiation when I have to work with open hot kiln. Clamshell is second in my opinion, before top loading.

A window costs but is worh every penny. Properly placed peep hole is cheaper. You must see at least 1/3 of the working surface.

The factory made kilns are all workhorses. I cannot warn off of any brand. The only caveat is brick lid. It tends to rain debris on the glass. yes, a controller that you can understand. Free programmability, no pre-set programs.

You want to get more confused? Please don't hesitate to ask.

-lauri

Reply to
Lauri Levanto

Hi again you say you love your bell jar,what kind or brand of kiln is that or is it one you built?Yes the controllers are very confusing,I have been looking at the ones made by skutt the glassmaster II what are your thoughts on them? Suzee

Reply to
misstiki

Bell jar kiln has a desk that forms the bottom. The sides and top like an upside down box are hoisted straight up. Therefore when hot manipulating, only the bottom radiates heat to my face and hands. I do not know if those are factory made. Mine is custom built.

|----|

=====

I do not know the American controllers. Mine is a Bentrup from Germany Checklist for the controller:

- does it have at least 8 program segments.

- does it set ramps by deg/hour OR time to next segment ( a matter of personal preference, I like the latter)

- does it have a backup batteru and recovery program for blackouts. (mine does not have, and I have to go to the studio and reset manually)

- do you really need stored programs. They make the thing more complicated, but are a blessing in production work.

-lauri

Reply to
Lauri Levanto

InspirePoint website is not affiliated with any of the manufacturers or service providers discussed here. All logos and trade names are the property of their respective owners.