Brother PR600 owner's manual: Setup location

Setup location

Setup the machine in a location that meets the following requirements.

• Position machine more than 50 mm (2 inches) from the wall

• Allow sufficient space around the machine

• Place no objects within the moving range of the embroidery frame

• Set-up machine near an electrical outlet

• Use a level and stable surface, such as a desk

• Use a surface that can support the weight of the machine (about 37 kg (81 lbs.))

• Allow open space around the ventilation slots at the bottom toward the back

CAUTION

● In order to prevent malfunctions or damage, do not set up the machine in a location exposed to the following conditions.

Direct sunlight

Liquids, such as water

Extreme dust

Blocked ventilation slots

Objects within the moving range of the embroidery frame

Insufficient space

Connection to extension cords or multiple adapters

An unstable surface

Extremely high or extremely low temperatures (The operating environment should be between 5 °C (40 °F) and 40 °C (104°F)

Setting Up the Machine 7

GETTING READY

Setting up the machine

When setting up the machine, adjust the legs so that the machine is steady.

1. Make sure that all packing tape affixed to the machine is peeled off and that all packing material is removed.

2. Set up the machine while making sure that there is sufficient space around it.

3. Adjust the legs so that the machine is steady. Use the included wrench to loosen the lock nut on the leg that you wish to adjust.

① Lock nut
② Adjustable foot nut
► The foot can be turned.

4. Use the included wrench to turn the adjustable foot nut on the foot. Turning the nut in direction ① lengthens the leg; turning the nut in direction ② shortens the leg.

① Adjustable foot nut
*   Adjust all four legs so that they securely contact the desk or table.

5. After adjusting the legs to the desired length, use the included wrench to tighten the nuts.

   ① Lock nut

6. Press down on each corner of the embroidery machine to check that it is stable. If it is still unstable, perform steps ❸ through ❺ again to adjust the legs.

Adjusting the operation panel position

Adjust the orientation and angle of the operation panel so it can easily be operated.

1 Loosen the thumb screw to bring the operation panel forward.

① Thumb screw

2 Adjust the operation panel to an easy-to-operate position, and then tighten the thumb screw.

3 Adjust the orientation of the operation panel. Loosen the thumb screw, adjust the operation panel to an easy-to-view orientation, and then tighten the thumb screw.

① Thumb screw

4 Adjust the angle of the operation panel. Loosen the thumb screw, adjust the operation panel to an easy-to-view angle, and then tighten the thumb screw.

① Thumb screw

Note

Using the disc-shaped screwdriver included, loosen and firmly tighten the thumb screw.

GETTING READY

Preparing the thread guide assembly

Raise the thread guide assembly. Locate the included Phillips screwdriver.

1. Using the Phillips screwdriver, loosen the screws on the left side of the thread guide assembly support so that the thread guide assembly can be raised. Remove screw ①, and then turn screw ② three or four times to loosen it.

① Remove the screw. ② Turn the screw three or four times to loosen it.

2. Raise thread guide into position and tighten the screws on the left and right sides of the thread guide assembly support.

3. Using the Phillips screwdriver, loosen the screws on the left and right sides of the thread guide assembly and lift up the thread guide so that it is level.

① Loosen Screws

4. Tighten the screws on the left and right sides of the thread guide assembly.

Note

• If the screws are not loosened enough, it may not be easy to move the thread guide assembly support and the thread guide. Do not apply extreme force when moving the thread guide assembly support and the thread guide. Be sure that the screws are loosened well enough before moving these parts.
• Be sure to tighten each screw well enough that the thread guide assembly support and the thread guide are secured.

Positioning the spool stand

Secure the spool stand in the embroidering position.

1. Loosen the thumb screw, and then open up the spool stand to the left and right.

① Thumb screw ② Spool stand

2. After the spool stand is fully opened up, tighten the thumb screw.

► Secure the spool stand in the opened position.

Attaching the embroidery frame holder

Attach the embroidery frame holder to the carriage.

1. Remove the two thumb screws of the embroidery frame holder.

① Thumb screws

2. Align the holes in the embroidery frame holder with the pins on the frame-mounting plate of the carriage.

① Pins on the frame-mounting plate ② Holes in the embroidery frame holder

Setting Up the Machine 11

GETTING READY

3 Secure the embroidery frame holder with the two thumb screws.

① Use the thumb screws removed in step 1.

Note

• Using the disc-shaped screwdriver included, firmly tighten the thumb screw.

This completes the preparation of the machine.

12

2 EMBROIDERING TUTORIAL

This chapter describes the basic embroidering operations in order—from turning on the machine and sewing a pattern to finishing sewing. Follow the steps of the tutorial to embroider a pattern and master the operation of this embroidery machine.

• Operating Precautions ........ 14
• Basic Procedures ........ 17
• Screen Quick Reference Guide ........ 48
• When You Have a Question, This May Help You ........ 57

Installing the Bobbin 1 Turning ON the Machine 2 Selecting an Embroidery Pattern 3 Editing the Embroidery Pattern 4 Specifying Embroidering Setting 5 Previewing the Image 6 Hooping the Fabric in the Embroidery Frame 7 Attaching the Embroidery Frame to the Machine 8 Checking the Embroidery Area 9 Upper Threading 10 Sewing the Embroidery 11 Checking the Thread Tension 12 Removing the Embroidery Frame and Fabric 13 Turning Off the Machine 14

EMBROIDERING TUTORIAL

Operating Precautions

The necessary points to ensure the correct operation of this machine are described below.

Power supply precautions

Be sure to observe the following precautions concerning the power supply.

WARNING

• Use only regular household electricity for the power source. Using other power sources may result in fire, electric shock, or damage to the machine.
• If any of the following occur, turn off the embroidery machine and unplug the power supply cord, otherwise a fire, an electric shock or damage to the machine may result.
  • When you are away from the machine.
  • After using the machine.
  • If a power outage occurs while the machine is being operated.
  • If the machine is not operating properly, for example, when there is a loose or cut connection.
  • During electrical storms.

CAUTION

• Do not plug this machine in with extension cords or multi-plug adapters with many other appliances plugged into them, otherwise a fire or an electric shock may result.
• Do not plug in or unplug the power supply cord with wet hands, otherwise an electric shock may result.
• When unplugging the power supply cord, be sure to first turn off the machine, and then grasp the plug when unplugging the cord. Pulling on the cord may damage it or result in a fire or an electric shock.
• Do not allow the power cord to be cut, damaged, modified, forcefully bent, pulled, twisted, or bundled. In addition, do not place heavy objects on the cord or expose it to heat, otherwise damage to the cord, fire or an electric shock may result. If the power supply cord or its plug is damaged, stop using the machine, and then take the machine to your nearest authorized dealer for repairs before continuing use.
• If the machine is not to be used for a long period of time, unplug the power supply cord, otherwise a fire may result.

14

Needle precautions

Be sure to observe the following precautions concerning the correct choice of needle for your machine.

CAUTION

• Your machine is designed to use household embroidery needles. The factory recommended needle is “HAX 130 EBBR” (Organ). Schmetz needles 130/705 H-E may be used as a substitute. Use of any other needles may break the needle or thread or damage the needle-threading mechanism or result to injuries.
• Never use bent needles. Bent needles can easily break, possibly resulting in injuries.

Checking the needle

Sewing with a bent needle is extremely dangerous since the needle may break while the machine is being operated.

Place the flat side of the needle on a flat surface and check that the distance between the needle and the flat surface is even. If the needle is bent or the tip of the needle is broken, replace the needle with a new one. (Refer to “Changing the Needle” on page 61.)

■ Good needle

Needle type marking Flat side Flat surface

■ Bad needle If the distance between the needle and the flat surface is not even, the needle is bent. Do not use a bent needle.

Flat surface

Bobbin precautions

Be sure to observe the following precautions concerning the bobbin.

CAUTION

• Only use prewound bobbin (COATS “L” type/TRU-SEW POLYESTER “Filaments”) or bobbins designed specifically for this machine. Use of any other bobbin may result in injuries or damage to the machine.

• Use a bobbin thread that has been correctly wound, otherwise the needle may break or the thread tension will be incorrect.

• When winding the bobbin, be sure to use cotton or spun polyester bobbin thread (between 74 dtex/2 and 100 dtex/2).

EMBROIDERING TUTORIAL

Upper thread recommendations

Be sure to observe the following recommendations concerning the upper thread.

Note

• It is recommended that rayon or polyester embroidery thread be used (120 den x 2 / 135 dtex x 2 / 40 weight (in Americas and Europe) / #50 (in Japan)).

Fabric recommendations

Be sure to observe the following recommendations concerning the fabric.

Note

• Fabric that is as thick as 1 mm (3/8 inch) can be embroidered. If thicker fabric is sewn, the needle may bend or break.
• When embroidering overlapping stitches, it is difficult for the needle to penetrate the fabric, possibly resulting in the needle bending or breaking.

Note

• Adhere stabilizers to thin or stretch fabrics. (Refer to “Attaching Iron-On Stabilizer (Backing) to Fabric” on page 64 for information)
• When embroidering large pieces of fabric, make sure that the fabric is not caught in the carriage.

Display recommendations

Be sure to observe the following recommendations concerning the use of the display.

Note

• Only touch the display with your finger or included touch pen. Do not use a mechanical pencil, screwdriver or any other hard or sharp object. In addition, do not apply extreme pressure to the display screen, otherwise damage to the display screen may result.

• All or part of the display screen may sometimes become darker or lighter due to temperature changes. This is not a sign of a malfunction. If the display is difficult to read, adjust its brightness. (Refer to “If the LCD cannot be read” on page 204.)

• The display may be dark immediately after the embroidery machine is turned on. This is a normal characteristic of the backlight and is not a sign of a malfunction. After approximately 10 minutes, the display should reach its normal level of brightness.

• If you are not directly facing the display, the colors may be distorted or the display may be difficult to read. This is a normal characteristic of the display and is not a malfunction. Be sure to sit in front of the display while using it.

16

Basic Procedures

Basic embroidering procedures are described below.
Check the overall procedure below, before operating the embroidery machine.

(Example) Embroidery pattern

The operations to embroider the pattern shown at the left are described on the following pages.
Although embroidering can continue without the pattern being edited or embroidering settings being specified, refer to page 118 for details on editing the patterns, and refer to page 85 for details on specifying embroidering settings.
Descriptions of the keys and other information that appear in the main LCD screens are provided in the tables on pages 48 to 56. Use these tables for quick reference.

The various operating precautions that must be observed during the basic procedures are provided on pages 14 to 16. These precautions must be strictly observed in order for the machine to function properly. Make sure to read these precautions.

EMBROIDERING TUTORIAL

1. Installing the Bobbin

The bobbin case is loaded with a bobbin wound with embroidery bobbin thread. Remove the bobbin case with the bobbin, check the amount of thread remaining in the bobbin, and then re-install the bobbin case with the bobbin. For precautions concerning the bobbin, refer to page 15.

Note

• A function that shows the amount of bobbin thread remaining is not available with this machine. Before starting to embroider, be sure to check the certain amount of bobbin thread remaining.
• Make sure to clean the bobbin case every time when change the bobbin. For details on cleaning the bobbin case, refer to "Cleaning the bobbin case" on page 185.

Removing the bobbin case

1 Open the hook cover. Pull the hook cover toward you.

2 Pull the thread picker toward you.

① Thread Picker To gain access to the bobbin case easily, pull the thread picker toward front.

Note

• Thread picker is a device that is used to hold the thread when begining to sew or when trimming the thread.

CAUTION

• The thread picker can only be moved within a certain range. Do not pull it with extreme force.

3 Grab the bobbin case latch, and remove the bobbin case.

① Latch

4 Close the latch, and then remove the bobbin from the bobbin case.

① Bobbin

5 Check the amount of bobbin thread remaining.

■ Oiling the machine After removing the bobbin case, apply oil to the machine. The race should be oiled. For details on oiling the machine, refer to "Oiling the machine" on page 186.

Note

• Make sure to oil the race of hook everyday when use the machine.

Installing the bobbin

1 Insert the bobbin into the bobbin case.

Note

• Check that the thread winds off the bobbin clockwise as shown in the illustration. If the bobbin is installed with the thread winding off in the opposite direction, the embroidery will not be sewn correctly.

2 Pass the thread through the thread slit and under the tension-adjusting spring.

① Thread slit ② Tension-adjusting spring

3 Pull the thread through the opening in the tension-adjusting spring.

① Pull out about 50 mm (2 inches) of thread.

Installing the bobbin case

1 Insert the bobbin case into the hook. Insert the bobbin case while aligning the tab on the bobbin case with the notch in the hook, as shown in the illustration.

① Tab Notch

• Fully insert the bobbin case until it snaps into place.

2 Close the hook cover.

Memo

• This embroidery machine is not equipped with a bobbin-winder. Use pre-wound (L type) bobbins.
• The optional bobbin winder (stand-alone type) and optional metal bobbins can also be used. (Refer to page 5, 168.)

Installing the Bobbin 19

EMBROIDERING TUTORIAL

2. Turning ON the Machine

Connect the power supply cord, and then turn on the embroidery machine. For precautions concerning the power supply, refer to page 14.

1 Plug the power supply cord into the machine.

2 Insert the plug of the power supply cord into a household electrical outlet.

3 Switch on the main power switch on the back of the machine to “I”.

► The buzzer beeps once and the LCD screen comes on.

4 When the screen shown below appears after the opening screen, touch OK.

► The pattern type selection screen appears, and the start/stop button lights up in red.

5 The carriage moves to its initial position.

• If the number 1 needle bar is not already at the embroidering position, the needle bar case moves and the number 1 needle bar moves to the embroidering position.

CAUTION

• Make sure to keep your hands and other items away from the carriage, in order to prevent any injuries.

Note

• (For U.S.A. only) This appliance has a polarized plug (one blade wider than the other). To reduce the risk of electrical shock, this plug is intended to fit into a polarized outlet in only one direction. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not modify the plug in any way.

Memo

• If the machine is turned off in the middle of embroidering, the machine will automatically save the design position when turned on again. At that time, you will be asked if you wish to continue embroidering or begin a new operation. (Refer to “Resume Embroidering After Turning Off the Machine” on page 81.)

20

Understanding the screens

When the machine is turned on and OK is touched, the pattern type selection screen appears. The operations described below will be entered using the operation panel. For precautions concerning the use of the touch panel, refer to page 16.

The screen that appears the next time that the embroidery machine is turned on differs depending on how the machine was previously turned off. (Refer to page 60.)

*The keys described above, except for the settings key, normally appear in the screens that will be described later and can be used. However, the settings key cannot be used in the embroidering screen.

EMBROIDERING TUTORIAL

Screen overview

The basic operation flow is shown below.

In the pattern type selection screen, select a pattern type. (Refer to page 24, 49) ① Touch this key to continue to the pattern editing screen. This key is not available unless a pattern type is selected.

In the pattern list screen, select the pattern. (Refer to page 23, 50) ① Touch this key to return to the pattern type selection screen. ② Touch this key to continue to the pattern editing screen.

In the pattern editing screen, edit the pattern. (Refer to page 25, 51)) ① Touch this key to return to the pattern type selection screen and add another pattern. ② Touch this key to continue to the embroidering settings screen.

In the embroidering settings screen, if it is a combined pattern, edit the entire pattern, specify the embroidering settings and check the embroidery area. (Refer to page 26, 53) ① Touch this key to quit the current operation and return to the pattern type selection screen. ② Touch this key to return to the pattern editing screen. ③ Touch this key to continue to the embroidering screen.

In the embroidering screen, check the thread colors assigned to the needle bars, and then install the upper threads. Touch the unlock key so that the start/stop button starts flashing in green and the embroidery machine is ready to begin sewing. After the embroidery is sewn, the embroidering settings screen appears. (Refer to page 33, 55) ① Touch this key to return to the embroidering settings screen.

22

3. Selecting an Embroidery Pattern

As an example, we will select the pattern shown at the right, on the last page of the embroidery patterns.

In the pattern type selection screen, select a pattern category (type). Pattern type selection screen (For details on the keys and other information on the screen, refer to page 49.)

① Pattern type keys ② On models without a built-in floppy disk drive, this appears only when the optional floppy disk drive is installed.

In the pattern list screen, search for the desired pattern, and then touch the key for the pattern. Pattern list screen (For details on the keys and other information on the screen, refer to page 50.)

① Pattern keys

Selecting an Embroidery Pattern 23

EMBROIDERING TUTORIAL

Selecting an embroidery pattern

We will select a floral on the second page.

1 Touch [icon] to select the embroidery patterns category.

► The list of embroidery patterns appears.

2 Touch [icon] and [icon] until the desired page is displayed.

For this example, display the last page.

• To select a pattern group other than the embroidery patterns, touch
  • ① Cancel key The pattern type selection screen appears.
• When there are many pages, the following appear:
  • ② Current page number
  • ③ Total number of pages
  • ④ Next page key Touch this key to display the next page. If the next page key is touched while the last page is displayed, the first page is displayed.
  • ⑤ Previous page key Touch this key to display the previous page. If the previous page key is touched while the first page is displayed, the last page is displayed.

3 Touch the desired pattern.

For this example, touch [icon].

► The selected pattern appears in the pattern display area.

• After a pattern is selected, the following appear:
  • ① Vertical length of the pattern
  • ② Horizontal width of the pattern
  • ③ Number of thread color changes
  • and the keys indicated by ④, which can be used to change the pattern size or mirror image the pattern. The functions that can be used differ depending on the type of pattern that is selected. (Refer to "Changing the size of the pattern" on page 100.)
• If the wrong pattern was selected or you wish to select a different pattern, touch the desired pattern.

4 Touch [icon] to display the next screen.

This confirms the pattern selection.

► The pattern editing screen appears.

24

4. Editing the Embroidery Pattern

When SET in the pattern list screen is touched, the pattern editing screen appears. From this screen, the pattern can be edited.

Pattern editing screen (For details on the keys and other information on the screen, refer to page 51.)

① Highlights the sizes of embroidery frames that can be used to sew the currently selected embroidery pattern ② Shows the size of the currently selected embroidery pattern The top value shows the height and the bottom value shows the width. ③ Shows the number of thread color changes for the currently selected embroidery pattern ④ Touch this key to delete the pattern, for example, if the wrong pattern was selected. No pattern is selected and the pattern type selection screen appears. ⑤ Continues to the next screen ⑥ Displays a preview image ⑦ Touch to edit the pattern.

In this example, we will not edit the pattern. Without performing any editing operations, continue to the next screen.

Continuing to the embroidering settings screen

1 Press EDIT END.

► The embroidering settings screen is displayed.

Memo

• If an operation in the pattern editing screen is interrupted and the machine is turned off, the operation can be continued after the machine is turned on again. When the machine is turned on again, you will be asked if you wish to continue the previous operation or begin a new one. (Refer to "Resume the Operation Being Performed Before the Machine Was Turned Off" on page 60.)

Editing the Embroidery Pattern 25

EMBROIDERING TUTORIAL

5. Specifying Embroidering Setting

When in the pattern editing screen is touched, the embroidering settings screen appears. From this screen, the entire pattern can be edited and embroidering settings can be specified. In addition, the embroidering position can be checked and a pattern can be saved for later use.

Embroidering settings screen (For details on the keys and other information on the screen, refer to page 53.)

① Restarts from the beginning ② Returns to the pattern editing screen ③ Displays a preview image ④ Touch to check the embroidering area. ⑤ Continues to the next screen ⑥ Touch to edit the pattern.

⑦ Touch these keys to specify how the pattern will be embroidered. ⑧ Touch to store the pattern. ⑨ In the embroidering settings screen, the embroidery frame guide in the pattern display area indicates the size of the installed embroidery frame.

In this example, we will not specify any of the embroidering settings. Continue with the next operation.

Memo

• If the embroidery frame is not positioned correctly when continuing to the embroidering settings screen, the embroidery frame is moved to the correct position at the same time that the embroidering settings screen is displayed. (Refer to “Embroidery Frame Position and Movement” on page 68.)

Memo

• If an operation in the embroidering settings screen is interrupted and the machine is turned off, the operation can be continued after the machine is turned on again. When the machine is turned on again, you will be asked if you wish to continue the previous operation or begin a new one. (Refer to “Resume the Operation Being Performed Before the Machine Was Turned Off” on page 60.)

26

6. Previewing the Image

You can view an image of the completed pattern within the embroidery frame.

Checking a preview image

Display the preview image to check that the embroidery will be sewn as desired.

1 Touch [icon].

► The preview image is displayed.

① Touch these keys to display the pattern in the various sizes of embroidery frames. The embroidery frames that appear in white on gray keys cannot be selected. ② Touch this key to display an enlarged view of the pattern.

2 Touch CLOSE to return to the previous screen.

Memo

• The preview image can also be displayed from the pattern editing screen.

Previewing the Image 27

7. Hooping the Fabric in the Embroidery Frame

After selecting the pattern to be embroidered, check which embroidery frames can be used to sew the pattern. Select the appropriate frame, and hoop the fabric and stabilizer in the embroidery frame. (Refer to “Attaching Iron-On Stabilizer (Backing) to Fabric” on page 64.) For precautions concerning the fabric, refer to page 16.

Note

• If the fabric is not taut, the pattern may be misaligned or the fabric may pucker. Follow the procedure described below to firmly stretch the fabric in the embroidery frame so that the fabric is not loose. In addition, be sure to work on a level surface when putting the fabric in the embroidery frame.

Hooping the fabric in the embroidery frame

1 Select an embroidery frame.

From the sizes of embroidery frames indicated in the screen, select the embroidery frame that you wish to use.

Embroidery frames that can be used appear darker (□) embroidery frames that cannot be used appear lighter (□).

Embroidery frame types

There are four sizes of embroidery frames. For details on the uses for each frame, refer to “Correctly Using the Embroidery Frames” on page 63.

CAUTION

• If an embroidery frame other than the four included frames are used, the embroidery frame may hit the presser foot, resulting in injuries.

Note

• The embroidery frame indicators show all embroidery frame sizes in which the embroidery pattern can be sewn. Be sure to use an embroidery frame of the most suitable size. If the embroidery frame that is too large is used, the pattern may be misaligned or the fabric may pucker. (Refer to “Correctly Using the Embroidery Frames” on page 63.)

■ Hooping fabric in the small embroidery frame The procedure for hooping fabric in the small embroidery frame is described below. The same procedure is used to hoop the fabric in the medium embroidery frame. For details on hooping fabric in the large embroidery frame and the extra-large embroidery frame, refer to “Hooping the Fabric” on page 65.

2 Loosen the screw on the outer frame.

① Screw

3 Place the fabric with the right side up on top of the outer frame.

• The outer frame does not have a front or back side. Either side can be used as the front.

4 Press the inner frame into the outer frame.

• Be sure that there are no wrinkles in the fabric after it is stretched in the embroidery frame.

5 Lightly tighten the screw, and then pull the edges of the fabric.

6 Securely tighten the screw, and then check that the fabric is taut.

• After stretching the fabric, lightly tapping it should produce a drum-like sound. • Firmly clamp together the inner and outer frames so that the bottom of the inner frame is lower than the bottom of the outer frame.

① Inner frame ② Outer frame ③ Bottom of inner frame

• Using the included disc-shaped screwdriver, firmly tighten the screw.

① Disc-shaped screwdriver

The amount that the fabric is stretched and the use of stabilizer material differ depending on the type of fabric being embroidered. Try various methods to achieve the best embroidering results. (Refer to “Hooping Techniques” on page 166.)

Memo ● This embroidery machine can also be used with the optional cap frames. (Refer to “Using the Optional Cap Frame” on page 169.)

Hooping the Fabric in the Embroidery Frame 29

EMBROIDERING TUTORIAL

8. Attaching the Embroidery Frame to the Machine

After hooping the fabric in the embroidery frame, attach the frame to the embroidery machine.

CAUTION

• If the embroidery frame is not correctly attached, the embroidery frame may hit the presser foot, resulting in injuries.
• When attaching the embroidery frame, make sure that the start/stop button is lit in red. If the start/stop button is flashing in green, the embroidery machine may start sewing. If the embroidery machine accidentally starts operating, injuries may result.
• When attaching the embroidery frame, make sure that the embroidery frame does not hit any other part of the embroidery machine.

Note

• Before attaching the embroidery frame, check that there is enough thread in the bobbin.

Attaching the embroidery frame

Adjust the width of the embroidery frame holder to the size of the embroidery frame, and then attach the embroidery frame to the machine. As an example, the procedure for attaching the small embroidery frame is described below.

Embroidery frame Holes Positioning slots

Left arm of embroidery frame holder Move the arm of the embroidery frame holder to the left or right to adjust it to the size of the embroidery frame.

Clip on embroidery frame holder. Insert the embroidery frame into the clips on the embroidery frame holder.

Positioning Pin

30

1 Loosen the two thumb screws on the embroidery frame holder.

If the screw is too tight, please use the included disc-shaped screwdriver.

① Left arm ② Thumb screws

► The left arm of the embroidery frame holder can be moved. • Only loosen the thumb screws a maximum of 2 turns counter clockwise. Do not remove the screw.

2 Move the left arm to align the screw on the right side with the mark for the embroidery frame to be installed, and then tighten the thumb screws.

For this example, align with mark ⑤.

① Mark for extra-large embroidery frame ② Mark for large embroidery frame ③ Mark for medium embroidery frame ④ Mark for embroidery frame for industrial embroidery machines (When using embroidery frames for industrial embroidery machines, THE MACHINE DOES NOT RECOGNIZE THE SEWING AREA OF THE FRAME. Be sure to use the trial sewing function to check that the pattern fits within the sewing area. If an embroidery frame for an industrial embroidery machine is installed, the right arm of the embroidery frame holder must also move. For details, refer to page 168.) ⑤ Mark for small embroidery frame ⑥ Align the screw with the mark.

Note ● Please firmly tighten the two thumb screws with included disc-shaped screwdriver. The machine will recognize the wrong frame size, if the two screws are not tightened.

► The embroidery frame holder is ready for the embroidery frame to be attached.

3 Hold the embroidery frame level, and then simultaneously align both the left and right mounts with the embroidery frame holder clips.

• The inner frame should be on top.

Note ● Incorrect frame positioning.

4 Insert the embroidery frame until it snaps into place.

① Make sure that the pins on the left and right arms of the embroidery frame holder fit into the positioning slot and hole on the embroidery frame.

Attaching the Embroidery Frame to the Machine 31