Woodturning Crafts

  1. Home
  2. Woodturning Crafts
7010 Threads Posts
to

Worth reading in Woodturning Crafts

update on my willow bowl project

http://www.frontiernet.net/~toller/bowl.jpg Came out really pretty, but the tear out killed it. It was not like normal...
8 comments posted 19yrs
posted by Toller
8 comments posted 19yrs posted by Toller

Oneway Laser Guided Hollowing System

Has anyone ever used the Oneway Laser Guided Hollowing System? If so, can you tell me how it works and how it compares...
3 comments posted 19yrs
posted by tajuly
3 comments posted 19yrs posted by tajuly

Where is there a Lathe Review?

I'm a relative newby, been turning for about a year and slowly getting a little better. I'm working on a used Rockwell...
5 comments posted 19yrs
posted by georgems
5 comments posted 19yrs posted by georgems

Slick Simple Method of Checking For "Fair Curve"

If you turn bowls you typically are shooting for a "fair curve" a continuous curved line, with no bumps or hollows. Ach...
4 comments posted 19yrs
posted by charlieb
4 comments posted 19yrs posted by charlieb

Notes from AAW 2007 in Portland

I've finally transcribed some of my notes from the Symposium onto my blog http://www.OhMyWoodness.com/blog They are shor...
0 comments posted 19yrs
posted by mvore
0 comments posted 19yrs posted by mvore

Jiggling Juglans Jugs in a.b.p.w.

This months turning club piece for the President's Challenge - picture in alt.binaries.pictures.woodworking. Coming up w...
1 comments posted 19yrs
posted by charlieb
1 comments posted 19yrs posted by charlieb

Spruce Burls!

While I was at Summer Camp last week as spiritual director, my wife got a call from a fellow I have never met who had h...
1 comments posted 19yrs
posted by darrellfeltmate
1 comments posted 19yrs posted by darrellfeltmate

Selecting Finish toEmphasize Figure in Wood

I've recently gotten some maple (called hard maple here in Arkansas- harder than red maple but not as hard as the sugar...
10 comments posted 19yrs
posted by kip055
10 comments posted 19yrs posted by kip055

Reversing a Delta Midi Lathe Motor

I am working on turning my Delta Midi Lathe into a dedicated outboard turning bowl lathe. I have reversed the headstock...
5 comments posted 19yrs
posted by steven_raphael
5 comments posted 19yrs posted by steven_raphael

Round skew 12mm

I have just brought a crown round skew 12mm. I am hoping that i can us this to finish the out side of my bowels, proir...
4 comments posted 19yrs
posted by Woodborg.2tixs5
4 comments posted 19yrs posted by Woodborg.2tixs5

delta rockwell parts needed

just picked up an old lathe model no. 46-111 i think ser # GD 8661. the threaded end of the head stock spindle is split...
4 comments posted 19yrs
posted by skeezics
4 comments posted 19yrs posted by skeezics

Vacuum pump trouble

I've seldom used my vacuum pump but when I recently tried all that happened was a continous hum. No suction. The gast p...
3 comments posted 19yrs
posted by mloconn1
3 comments posted 19yrs posted by mloconn1

stone crusher for inlay material

I use crushed stone such as Turquoise and Malachite on some of my turnings. The cost for already crushed stone ranges f...
18 comments posted 19yrs
posted by wskossack
18 comments posted 19yrs posted by wskossack

For those waiting for thier glue gun to warm up.

Sort of an addition to the face plate thread, which I have deleted.. sorry.. http://www.pennstateind.com/store/gg100.ht...
8 comments posted 19yrs
posted by mac.splinters
8 comments posted 19yrs posted by mac.splinters