Woodturning Crafts

  1. Home
  2. Woodturning Crafts
7010 Threads Posts
to

Worth reading in Woodturning Crafts

newbie lathe motor question

Hi, pardon my ignorance, but I have recently acquired an old Boice-Crane lathe that doesn't have a motor. Any suggestion...
8 comments posted 21yrs
posted by richg
8 comments posted 21yrs posted by richg

FA: Fine Woodworking back issues

http://search.ebay.com/_W0QQgotopageZ1QQsassZbar2112QQsorecordsperpageZ50QQsosortorderZ1QQsosortpropertyZ1
0 comments posted 21yrs
posted by amatlosz
0 comments posted 21yrs posted by amatlosz

glue up advice needed (see pix in a.b.p.w)

I boughta "ringmaster" (see http://www.ringmastertool.com/ but if youlook at the pic you will notice that in trying to...
0 comments posted 21yrs
posted by myxpykalixNOSPAM
0 comments posted 21yrs posted by myxpykalixNOSPAM

SuperNova 2 chuck

I ordered a Supernova chuck and cole jaws from the KMS Tools website. It was the best prices I found. That night Bob Ga...
3 comments posted 21yrs
posted by gwader
3 comments posted 21yrs posted by gwader

New Arizona Woodcraft store!

Woodcraft has opened a new store in Chandler, AZ. On the coorner of Elliot and Arizona Ave. AZCRAIG www.azcraig.us
0 comments posted 21yrs
posted by kayakaz
0 comments posted 21yrs posted by kayakaz

Tech question for woodturners

I have noticedon several lathes that I use that the spur center appears to have rings cut around the taper and that the...
1 comments posted 21yrs
posted by respite95
1 comments posted 21yrs posted by respite95

PING: Andy Hilton

Anybody heard from Andy Hilton lately? Email to him has gone unanswered. He used to contribute here quite regularly. --...
1 comments posted 21yrs
posted by chaz3913NOSPAM
1 comments posted 21yrs posted by chaz3913NOSPAM

OT Birthday

HAPPY BIRTHDAY US MARINES!!!
4 comments posted 21yrs
posted by zwwizard
4 comments posted 21yrs posted by zwwizard

Spindle turning Speed

What would be a good RPM range for rough turning a 2" square of walnut 24 inches long? -TIA
12 comments posted 21yrs
posted by nottodaythanks
12 comments posted 21yrs posted by nottodaythanks

What is an indexingt pin?

I saw a picute the other day of the headstock of a lathe and there was a small pin that stuck out just next to the spin...
1 comments posted 21yrs
posted by nottodaythanks
1 comments posted 21yrs posted by nottodaythanks

Today's Hint - Don't do things like this

I am sure I am not the only one who carries a portable phone handset to the garage shop. I recommend not laying the han...
100 comments posted 21yrs
posted by rbrogan
100 comments posted 21yrs posted by rbrogan

debaiting a turning project

I just got the piece of highly figured maple shown at the link http://home.comcast.net/~wskossack/block.htmlNow the que...
0 comments posted 21yrs
posted by wskossack
0 comments posted 21yrs posted by wskossack

Turners in South Dallas area

I would like to start a weekly gathering of turners in South Dallas area. Tentative day is Tuesday. I am a member of Da...
0 comments posted 21yrs
posted by akransom
0 comments posted 21yrs posted by akransom