Woodturning Crafts

  1. Home
  2. Woodturning Crafts
7010 Threads Posts
to

Worth reading in Woodturning Crafts

Ping Ingram on Fluting

Not getting all messages through my ISP, but here's one of many http://www.kestrelcreek.com/toc.htm?id=22&cat=techFine W...
0 comments posted 22yrs
posted by george
0 comments posted 22yrs posted by george

Barrel Trimmer/ Pen Mill

I have heard some say that barrel trimmers/pen mills get dull rather quickly. I have been using a disc sander to square...
6 comments posted 22yrs
posted by matman_2002NOSPAM
6 comments posted 22yrs posted by matman_2002NOSPAM

Apple

Thanks to nature (wind) and my neighbor (cum chainsaw), I've just acquired a sizeable lot of apple wood. Some of the pi...
11 comments posted 22yrs
posted by maxprop
11 comments posted 22yrs posted by maxprop

Re: Steve Russell's "Back in the Saddle"...

Hello Ken, It would be easier to say what I have not been experimenting with lately... :-) I have recently completed so...
2 comments posted 22yrs
posted by benzer
2 comments posted 22yrs posted by benzer

Re: CA ?s

> I had my flexible CA in a 2 oz bottle thicken up. I was considering = getting > a 16 oz. bottle of thick from Starbon...
7 comments posted 22yrs
posted by danbollinger
7 comments posted 22yrs posted by danbollinger

turning blanks UK

I'm off to Scotland/England for a couple of weeks and wondering where the best place in the Norfolk area might be to pic...
0 comments posted 22yrs
posted by wgooch
0 comments posted 22yrs posted by wgooch

Re: fine lines between segments

> My question: how does the artist/turner insert those perfect > white or black lines between the segments? Does he glu...
3 comments posted 22yrs
posted by harrypye
3 comments posted 22yrs posted by harrypye

Re: newbie question:Indexing?

The indexing knob is used to hold work on a lathe stationary while you cut a flute or a reed with a router setup. There...
1 comments posted 22yrs
posted by barry712
1 comments posted 22yrs posted by barry712

Re: Arrowmont bound!

Greetings and Salutations... >Hi, All! > >I'm registered to attend a week-long session at Arrowmont starting on >Sunday...
3 comments posted 22yrs
posted by xmundt
3 comments posted 22yrs posted by xmundt

Re: What should I use for finishing bowls?

> I want a good finish for my natural edge bowls. I've used tung oil, tung > oil mixed with mineral spirit and now use...
11 comments posted 22yrs
posted by onlnlowe
11 comments posted 22yrs posted by onlnlowe

Woodturning website

Hi Just revised my website on beginner woodturning and would appreciate comments and ideas on improvements. http://www.i...
1 comments posted 22yrs
posted by woodturns
1 comments posted 22yrs posted by woodturns

Re: Suggestions on new chuck

Good, but I would get a cup center. I have had _much_ better experience with it over the single point. Kids catch a bit...
0 comments posted 22yrs
posted by george
0 comments posted 22yrs posted by george

Re: Drill Press Table Lift Easier Than I Thought

On Thu, 5 Aug 2004 15:48:04 -0500, "RonB" vaguely proposed a theory ......and in reply I say!: remove ns from my header...
0 comments posted 22yrs
posted by nsnsafemail
0 comments posted 22yrs posted by nsnsafemail

Burl Preparation Question

Hi Folks, A neighbour just presented me with a number of burls. A centre-split 4-foot length of 16 inch diameter log co...
4 comments posted 22yrs
posted by thostorey
4 comments posted 22yrs posted by thostorey

Mini lathe semi-mobile stand (pictures)

I have been planning to pick up a Jet mini lathe for some time, based mostly on favorable reviews from this group. I ha...
2 comments posted 22yrs
posted by kvaughn65
2 comments posted 22yrs posted by kvaughn65