Latest threads in Woodturning Craftsshow only best voted threads
| Subject | Author | Posted | Replies | |
|---|---|---|---|---|
|
|
OT Mark Duginske's Recent Arrticle on Bandsaw Circle Cutting Jig??? Anybody?
Rockler's makes a circle-cutting kit for bandsaws or tablesaws. I have it and have used it. Essentially, you add an auxillary wooden table, cut a dado that extends to the right, away from the blade...
3
|
20 years ago
|
3 | |
|
|
Nova 3000 speed problem
in article x7icnSCC Ray Sandusky at wrote on 8/21/03 3:00 PM: Leeson 1HP
2
|
20 years ago
|
2 | |
|
|
Sioux Angle Drill
Thanks Bill, Worked great, used a Dremel tool and now I have the bearing off. Now looking for source of replacement bearings. No luck so far. When I do find a supplier I'll go ahead and order several....
1
|
20 years ago
|
1 | |
|
|
Re: finish question -- wax on oil, timing
D K Woods wrote in news: The Watco I use recommends a 48-72 hour waiting period after the oil application before any top coats are put on. I have used penetrating finishes like Watco with good results...
—
|
20 years ago
|
— | |
|
|
Re: First attempt at Bowl turning
When you get to the point where you are doing the final finishing cuts, resharpen your gouge to make sure you have a good edge and make light cuts. It also helps to have the edge of the gouge which is...
3
|
20 years ago
|
3 | |
|
|
Re: Broken oneway :(
Kevin, I had the same symptoms on my 2436 and it was just as you described. The door switch had gone out of adjustment. I by passed it and all problems went away. I readjusted the door switch and have...
3
|
20 years ago
|
3 | |
|
|
helmet cameras
This sounds like the best idea yet I will try this Thanks to all Jim Driskell
7
|
20 years ago
|
7 | |
|
|
One-way Website?
Located where they are (Stratford, Ont) it is possible that power might not have been reliable in the aftermath of the blackout. I know that some areas of Ontario were still having intermitent outages...
2
|
20 years ago
|
2 | |
|
|
Face Mask - a cry for help
[Posted and mailed] [snip] Thanks for that, I had a nagging feeling I'd seen something similar somewhere, I give it a try. Dave
3
|
20 years ago
|
3 | |
|
|
Metal spinning
Does anyone know the identity of the craftsman doing the metal spining in HGTV's commercial for "Modern Masters?" Thanks!! Dave Colorado
—
|
20 years ago
|
— | |
|
|
Shopsmith ER
I am looking for a speedchanger for a Shopsmith ER. Can anybody help? Al
—
|
20 years ago
|
— | |
|
|
What happened to my Poplar?
Rob, you should be posting those photos in your own album in WOW (World of Woodturners). Email me ( if you want a username and password I've had the same thing with poplar. It's a junk wood around...
4
|
20 years ago
|
4 | |
|
|
Re: Last Year Oak, This Year Beech
Thanks for the heads up. Fortunately I have plenty of hard maple and yellow birch in there as well. I know they turn and burn just fine. SWMBO and I are our chimney sweeps! wrote:
2
|
20 years ago
|
2 | |
|
|
Looking for plans for a Fancy Top
Thank you for the help. It is greatly appreciated. F D http://www.utahyoyo.com/tops/ http://www.roystopshop.com/ http://www.uncledonsmechanicals.com/topshow.htm
3
|
20 years ago
|
3 | |
|
|
Newbie Question: Lathe Upgrade Choice
Hi Jon, I have a Delta 1642 with a 2HP motor. It has a three step pulley giving the VFD three ranges of operation. Being able to move the headstock anywhere on the bed is one of the greatest features...
2
|
20 years ago
|
2 |