Woodturning Crafts

  1. Home
  2. Woodturning Crafts
7010 Threads Posts
to

Worth reading in Woodturning Crafts

WANTED: PLANER

I am wanting to buy a used thickness planer of at least 12". This should be in or around the Houston area. May even con...
1 comments posted 21yrs
posted by aeschelon
1 comments posted 21yrs posted by aeschelon

Wooden pens

Hi, does anyone know a CNC that may carve the wooden cap or body of a pen with images of temples, historic moments, etc...
3 comments posted 21yrs
posted by fabrimo
3 comments posted 21yrs posted by fabrimo

ANNOUNCEMENT: Wikipedia Woodworking project

Wikipedia is a completely free, non-commercial, online encyclopedia that anyone can edit. Wikipedia has rapidly become...
0 comments posted 21yrs
posted by recnorm
0 comments posted 21yrs posted by recnorm

Cub Woodwriter?

Has anyone ver used this Cub woodwriter for there wood projects.... here is a link http://www.woodturnerscatalog.com/cgi...
3 comments posted 21yrs
posted by gregg
3 comments posted 21yrs posted by gregg

Celtic Knots

I would like to turn some pens with celtic knots inbedded, impressed, or with the knots on the band or pocket clip. Doe...
0 comments posted 21yrs
posted by harolda
0 comments posted 21yrs posted by harolda

Turning Mishap

I had had a pretty nice piece of highly figured maple in the shop for a couple of years. I pulled it out last Saturday...
1 comments posted 21yrs
posted by barry712
1 comments posted 21yrs posted by barry712

Got The Chuck & Fear For My Bearings

PIcked up the SuperNova2 and the Pin Jaws. Cleaned them up put the chuck on the JET midi lathe and now I'm concerned ab...
54 comments posted 21yrs
posted by charlieb
54 comments posted 21yrs posted by charlieb

Good set of Woodturning tools

I am looking to buy a set of wood lathe tools. Could someone suggest a good set that is not too expensive? Thanks
9 comments posted 21yrs
posted by ssnt1129
9 comments posted 21yrs posted by ssnt1129

Watco, BLO and buffing

Greetings!! I have a quick question regarding buffing with the Beall system. In the the Beall buffing instructions, the...
3 comments posted 21yrs
posted by rmcconachie
3 comments posted 21yrs posted by rmcconachie

motor/switch/wiring problem

My old Delta lathe refused to start a day after turning a 11" bowl without incident. Before I try to distort my body in...
14 comments posted 21yrs
posted by Galanw
14 comments posted 21yrs posted by Galanw

Is Everyone Gone For The Weekend?

Haven't seen a new post from this group since one (and only one) yesterday morning. Just wanted to mention that there i...
5 comments posted 21yrs
posted by fredbear34
5 comments posted 21yrs posted by fredbear34

Saw question.

I know it doesn't make much sence to ask this question on the turning group, but it does sorta when you think about it....
5 comments posted 21yrs
posted by mgburr
5 comments posted 21yrs posted by mgburr

Musing about one cure for turner's burnout. Long

For some there comes an occasional burnout stage in our addiction. A pole lathe. a green limb and one or two homemade o...
6 comments posted 21yrs
posted by almcc
6 comments posted 21yrs posted by almcc

Belated thanks to Steve Worcester

Hi Steve, I haven't checked rcw archives since my vacation to Maine instead of Kansas, so I don't know if there have be...
2 comments posted 21yrs
posted by almcc
2 comments posted 21yrs posted by almcc