Woodturning Crafts

  1. Home
  2. Woodturning Crafts
7010 Threads Posts
to

Worth reading in Woodturning Crafts

Ode to a Wood Turner

May your bevels always rub.......... May your tools always be razor sharp............ May you never get a catch............
4 comments posted 23yrs
posted by barry712
4 comments posted 23yrs posted by barry712

Yorkcraft Lathe

Hi All, My wife and I are seriously considering a 12" lathe. I've read various posts on the jet, grizzly and harbor fre...
0 comments posted 23yrs
posted by jgoldrick
0 comments posted 23yrs posted by jgoldrick

Hauling Uphill

Hi. We'll be cutting down trees, removing overgrown brush, etc. from about 4000 sq. ft. of our downsloping lot. I've re...
24 comments posted 23yrs
posted by gregfocker
24 comments posted 23yrs posted by gregfocker

I guess I'm confused

I just purchased a Sorby set from Sears. $180 for six tools. Not a bad deal for me. It is the 67HS set. I needed and wi...
50 comments posted 23yrs
posted by edingtonrp
50 comments posted 23yrs posted by edingtonrp

Linda Van G Woodturning Demo

Corfu, New York - Saturday, September 20, 2003 The Pembroke Woodturners Guild in Corfu, NY will host Linda Van Gehuchte...
4 comments posted 23yrs
posted by lkanaby
4 comments posted 23yrs posted by lkanaby

grinding flutes

The email addresses seem different, but I assume the Ed French who wrote a very nice article on making gouges for the F...
1 comments posted 23yrs
posted by almcc
1 comments posted 23yrs posted by almcc

OT (sorta) Table saws

Thinking of buying a table saw, looked at Sears. Some are direct drive, others belt drive. Higher priced ones have belt...
5 comments posted 23yrs
posted by ricksub
5 comments posted 23yrs posted by ricksub

pen turning

i'm new to pen turning and have been using spray on laquer for the finish i also use hut crystal coat.my question is whi...
1 comments posted 23yrs
posted by dennislb
1 comments posted 23yrs posted by dennislb

question on plane

Recently (while digging in my parents' basement) I found a plane (in teh original box) apparently never used. the box s...
5 comments posted 23yrs
posted by rmcconachie
5 comments posted 23yrs posted by rmcconachie

What to Say

I recently finished my first bowl intended to be a gift -- a wedding gift. It's made of Jatoba (Brazillian Cherry) and...
5 comments posted 23yrs
posted by dickjacobs
5 comments posted 23yrs posted by dickjacobs

What to Write

I recently finished my first bowl intended to be a gift -- a wedding gift. It's made of Jatoba (Brazillian Cherry) and...
4 comments posted 23yrs
posted by dickjacobs
4 comments posted 23yrs posted by dickjacobs

Tools

Does anyone out there know if any company is still making the turning gouges with the replaceable tips. They were being...
5 comments posted 23yrs
posted by colran
5 comments posted 23yrs posted by colran

Walker-Turner Lath

I have a Walker-Turner lath that I acquired recently. I have located the company on their web site. I think the circa i...
1 comments posted 23yrs
posted by darvince
1 comments posted 23yrs posted by darvince

WTB - Stronghold Chuck

Greetings! After doing my research and comparing features of one chuck to another, I have decided that the Oneway Stron...
13 comments posted 23yrs
posted by rmcconachie
13 comments posted 23yrs posted by rmcconachie